reverse-phase HPLC comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Last reviewed on 2025-10-03. Where a claim depends on a specific study, the study is described rather than over-claimed.
Storage and handling conditions affect both peptide stability and the accuracy of later purity tests. Lyophilized powders are commonly kept desiccated at -20 °C or below, while reconstituted solutions require a defined buffer, pH, and temperature range. Repeated freeze-thaw cycles can promote aggregation, oxidation, or hydrolysis over time. Each cycle may alter the chromatogram and complicate comparison with earlier results. Stability data, when available, should guide handling intervals and solvent choice.
Independent verification is used when a supplier result needs confirmation or when a material supports regulated work. A second laboratory can repeat reverse-phase HPLC and mass spectrometry on the same sample. Discrepancies may arise from different columns, gradients, detection wavelengths, or sample preparation. Moisture uptake and counterion content can lower net peptide mass without changing area percent. Documentation of methods and raw data helps distinguish analytical variation from a true quality difference.
Quality control for peptides begins with a documented specification that states the required purity, identity, and appearance. Suppliers often release research-grade material at 95% or greater by HPLC area, but this threshold is not universal. A certificate of analysis typically records the lot number, sequence, test methods, and measured values. The document allows a user to compare batches and to trace deviations. Specifications should match the intended use rather than a generic label.
Other methods address specific purity concerns. Amino acid analysis gives compositional data after hydrolysis, while capillary electrophoresis separates by charge-to-mass ratio. Karl Fischer titration measures residual water, and gas chromatography can detect residual solvents. Nuclear magnetic resonance can identify organic impurities but is less sensitive for trace levels. No single test covers all possible impurities, so purity testing usually combines orthogonal methods and reports the conditions used. The choice of methods is guided by the impurity classes of interest.
Reverse-phase high-performance liquid chromatography (RP-HPLC) is widely used to estimate peptide purity. It separates components by hydrophobicity on a column with a water-organic mobile phase. Ultraviolet absorbance at 214 nm or 220 nm detects peptide bonds. The main peak area as a percentage of total peak area gives a purity figure. This figure depends on column, gradient, wavelength, and how peaks are integrated, so it is method-specific rather than absolute.
Mass spectrometry provides complementary information by measuring molecular mass. Electrospray ionization or matrix-assisted laser desorption/ionization can confirm the expected peptide mass and reveal related impurities with different masses. It does not directly quantify all species because ionization efficiency varies. When coupled to liquid chromatography, LC-MS can assign masses to chromatographic peaks. This helps distinguish target peptide from truncation, oxidation, or deletion products. Mass accuracy and resolution determine how confidently a mass can be matched to a proposed structure.
| Property | Value | Notes |
|---|---|---|
| Typical storage temperature | -20 °C or below | For lyophilized powder; keep desiccated. |
| Short-term solution storage | 2-8 °C | For reconstituted peptide; follow stability data. |
| Common research-grade specification | 95% or greater by HPLC area | Widely cited threshold; not a universal standard. |
| Documentation | Certificate of analysis | Lists lot, sequence, method, purity, and storage guidance. |
| Independent verification | Second-laboratory HPLC and mass spectrometry | Repeats tests on submitted sample to confirm supplier result. |
Additional techniques address components that reversed-phase chromatography may not resolve. Ion-exchange chromatography separates by charge, size-exclusion chromatography detects aggregates, and capillary electrophoresis offers high separation efficiency. Water content is measured by Karl Fischer titration, residual solvents by gas chromatography, and elemental impurities by inductively coupled plasma mass spectrometry. Amino acid analysis or nitrogen determination can estimate peptide content on a mass basis. Purity is frequently reported as area percent, yet standardized comparison across laboratories remains an open question because methods and reporting practices differ.
Peptide purity testing measures how much of a sample consists of the intended peptide sequence compared with related substances, water, counterions, and residual solvents. No single analytical method captures all of these components at once. Reversed-phase high-performance liquid chromatography with ultraviolet detection is widely used because it separates peptides by hydrophobicity. The reported purity value therefore depends on the chosen method, column, mobile phase, and detection wavelength. Established practice treats purity as method-dependent rather than an absolute property of the material.
Impurity profiles can include deletion peptides, oxidized forms, truncated sequences, and residual solvents. Some impurities arise during synthesis, cleavage, or purification, while others form during storage. Purity testing often focuses on peptide-related impurities, whereas residual solvents and counterions require separate assays. The significance of a given impurity depends on its amount and properties, which may not be established for a research peptide. Reporting an impurity profile is more informative than reporting a single purity number.
Peptide purity specifications describe the minimum acceptable result from a defined test. A certificate of analysis may list HPLC purity, mass spectrometry identity, appearance, and counterion content. Specifications are method-dependent, so a value obtained with one gradient or wavelength may differ from another. For research use, common thresholds include 95% and 98% by RP-HPLC, but the appropriate limit depends on the application. The specification should always name the analytical method and acceptance criterion.
Quality control includes system suitability, blank injections, and reference standards. System suitability checks column performance and retention time reproducibility, while blank runs detect carryover or mobile-phase contaminants. Reference standards help calibrate retention time and detector response. Without these controls, a purity value is difficult to compare across laboratories or over time. Documentation of instrument settings and integration parameters is also part of quality control, and acceptance criteria should be set before samples are analyzed.
Handling practices reduce the risk of contamination and degradation. Hygroscopic peptides should be equilibrated to room temperature before opening to prevent condensation on the powder. Weighing and reconstitution in a controlled environment limit exposure to moisture and airborne particles. Aliquotting reconstituted solutions avoids repeated freeze-thaw cycles that can cause aggregation or precipitation. When a purity specification is not met, investigation may consider synthesis byproducts, purification losses, storage conditions, and analytical variability rather than a single cause.
Peptide purity can change during storage, handling, and reconstitution, and lyophilized peptides are generally more stable than solutions because water promotes hydrolysis and aggregation. Residual moisture, oxygen, and trace metals can accelerate degradation even in solid form. Temperature fluctuations during shipping may cause condensation and local moisture uptake. Quality control therefore includes appearance, water content, and analytical testing before and after storage challenges. Peptides containing cysteine, methionine, or tryptophan are especially susceptible to oxidation, while asparagine and glutamine residues can deamidate under neutral or alkaline conditions.
Analytical quality control compares a stored sample against a baseline profile. Reverse-phase chromatography remains common, but stability studies may also use mass spectrometry to detect oxidation, deamidation, or truncation products. Accelerated aging at elevated temperature can reveal degradation pathways, although extrapolation to room temperature is uncertain. Forced degradation studies expose peptides to heat, light, acid, base, and oxidants to identify likely breakdown products. Documentation should record lot number, storage history, and the exact method used for each measurement.
Aaron R. Wheeler is a Canadian chemist who is a professor of chemistry and biomedical engineering at the University of Toronto since 2005 with cross-appointment at Institute of Biomedical Engineering and Terrence Donnelly Centre for Cellular and Biomolecular Research. His academic laboratory is located at Lash Miller Chemical Laboratories and Terrence Donnelly Centre for Cellular and Biomolecular Research at the University of Toronto. In 2005, Wheeler was appointed as assistant professor and Tier II Canada Research Chair then promoted to associate professor in 2010, full professor in 2013, and in 2018 he became the Tier I Canada Research Chair in Microfluidic Bioanalysis. Wheeler did his undergraduate studies at Furman University in Greenville, SC then he joined Stanford University from 1997 to 2003 to obtain his Ph.D. in chemistry under supervision of Richard Zare . Following graduation, he took a two-year NIH postdoctoral fellowship at UCLA till 2005.
The positive transcription elongation factor, P-TEFb, is a multiprotein complex that plays an essential role in the regulation of transcription by RNA polymerase II (Pol II) in eukaryotes. Immediately following initiation Pol II becomes trapped in promoter proximal paused positions on the majority of human genes (Figure 1). P-TEFb is a cyclin dependent kinase that can phosphorylate the DRB sensitivity inducing factor (DSIF) and negative elongation factor (NELF), as well as the carboxyl terminal domain of the large subunit of Pol II and this causes the transition into productive elongation leading to the synthesis of mRNAs. P-TEFb is regulated in part by a reversible association with the 7SK snRNP. Treatment of cells with the P-TEFb inhibitors DRB or flavopidirol leads to loss of mRNA production and ultimately cell death. P-TEFb was identified and purified as a factor needed for the generation of long run-off transcripts using an in vitro transcription system derived from Drosophila cells.
The American Society for Biochemistry and Molecular Biology (ASBMB) is a learned society that was founded on December 26, 1906, at a meeting organized by John Jacob Abel (Johns Hopkins University). The roots of the society were in the American Physiological Society, which had been formed some 20 years earlier. ASBMB is the US member of the International Union of Biochemistry and Molecular Biology. The ASBMB was originally called the American Society of Biological Chemists, before obtaining its current name in 1987. The society is based in Rockville, Maryland. ASBMB's mission is to advance the science of biochemistry and molecular biology through publication of scientific and educational journals, the organization of scientific meetings, advocacy for funding of basic research and education, support of science education at all levels, and by promoting the diversity of individuals entering the scientific workforce. The organization currently has over 12,000 members.
When measured by fatalities per person transported, however, buses are the safest form of transportation. The number of air travel fatalities per person are surpassed only by bicycles and motorcycles. This statistic is used by the insurance industry when calculating insurance rates for air travel. For every billion kilometers traveled, trains have a fatality rate that is 12 times higher than that of air travel, and the fatality rate for automobiles is 62 times greater than for air travel. By contrast, for every billion journeys taken, buses are the safest form of transportation; using this measure, air travel is three times more dangerous than car transportation, and almost 30 times more dangerous than travelling by bus. A 2007 study by Popular Mechanics magazine found that passengers sitting at the back of an aeroplane are 40% more likely to survive a crash than those sitting at the front. The article quotes Boeing, the FAA, and a website on aircraft safety, all of which claim that there is no "safest" seat. The study examined 20 crashes, not taking into account the developments in safety after those accidents. However, a flight data recorder is usually mounted in the aircraft's empennage (tail section) where it is more likely to survive a severe crash. Between 1983 and 2000, the survival rate for people in U.S. plane crashes was greater than 95 percent.
Tranexamic acid is frequently used following major trauma. Tranexamic acid is used to prevent and treat blood loss in a variety of situations, such as dental procedures, heavy menstrual bleeding, and surgeries with high risk of blood loss. Tranexamic acid has been found to decrease the risk of death due to any cause in people who have significant bleeding due to trauma. It is most effective if taken within the first three hours following major trauma. It also decreases the risk of death if given within the first three hours of brain injury.
Sources: en.wikipedia.org
In both pharmacology and nutrition sciences, bioavailability is measured by calculating the area under curve (AUC) of the drug concentration time profile. Bioavailability is a term used to describe the percentage of an administered dose of a xenobiotic that reaches the systemic circulation unchanged. It is denoted by the letter f (or, if expressed in percent, by F). In nutritional science, which covers the intake of nutrients and non-drug dietary ingredients, the concept of bioavailability lacks the well-defined standards associated with the pharmaceutical industry. The pharmacological definition cannot apply to these substances because utilization and absorption is a function of the nutritional status and physiological state of the subject, resulting in even greater differences from individual to individual (inter-individual variation). Therefore, bioavailability for dietary supplements can be defined as the proportion of the administered substance capable of being absorbed and available for use or storage.
Dyneins, one of the three major classes of motor protein, are AAA proteins which couple their ATPase activity to molecular motion along microtubules. The AAA-type ATPase Cdc48p/p97 is perhaps the best-studied AAA protein. Misfolded secretory proteins are exported from the endoplasmic reticulum (ER) and degraded by the ER-associated degradation pathway (ERAD). Nonfunctional membrane and luminal proteins are extracted from the ER and degraded in the cytosol by proteasomes. Substrate retrotranslocation and extraction is assisted by the Cdc48p(Ufd1p/Npl4p) complex on the cytosolic side of the membrane. On the cytosolic side, the substrate is ubiquitinated by ER-based E2 and E3 enzymes before degradation by the 26S proteasome.
As with bacterial classification, identification of bacteria is increasingly using molecular methods, and mass spectroscopy. Most bacteria have not been characterised and there are many species that cannot be grown in the laboratory. Diagnostics using DNA-based tools, such as polymerase chain reaction, are increasingly popular due to their specificity and speed, compared to culture-based methods. These methods also allow the detection and identification of "viable but nonculturable" cells that are metabolically active but non-dividing. The main way to characterize and classify these bacteria is to isolate their DNA from environmental samples and mass-sequence them. This approach has identified thousands, if not millions of candidate species. Based on some estimates, more than 43,000 species of bacteria have been described, but attempts to estimate the true number of bacterial diversity have ranged from 107 to 109 total species—and even these diverse estimates may be off by many orders of magnitude.
PABA is an intermediate in the synthesis of folate by bacteria, plants, and fungi. Many bacteria, including those found in the human intestinal tract such as E. coli, generate PABA from chorismate by the combined action of the enzymes 4-amino-4-deoxychorismate synthase and 4-amino-4-deoxychorismate lyase. Plants produce PABA in their chloroplasts, and store it as a glucose ester (pABA-Glc) in their tissues. The malarial protozoan Plasmodium only make PABA when necessary, preferring to get it from the surroundings if able to. Some bacteria, including a few found in the human microbiome, are unable to make PABA for themselves but can use PABA to make folate. A few are very efficient at the PABA-to-folate conversion despite not making their own PABA. Sulfonamide drugs are structurally similar to PABA, and their antibacterial activity is due to their ability to interfere with the conversion of PABA to folate by the enzyme dihydropteroate synthetase. Thus, bacterial growth is limited through folate deficiency.
Public health laboratories operate as a first line of defense to protect the public against diseases and other health hazards. Day-to-day operations range from testing water and food, checking for toxins in soil, and investigating new strains of infectious diseases, such as COVID-19 or Ebola. Every US state and territory, and the District of Columbia, has a central governmental public health laboratory that performs testing and other laboratory services on behalf of the entire jurisdiction. In addition, some states have local public health laboratories ranging in size from large metropolitan laboratories with over a hundred scientists to small rural laboratories with one or two staff that support local public health.
Sources: en.wikipedia.org
Bodybuilding supplements are dietary supplements commonly used by those involved in bodybuilding, weightlifting, mixed martial arts, and athletics for the purpose of facilitating an increase in lean body mass. Bodybuilding supplements may contain ingredients that are advertised to increase a person's muscle, body weight, athletic performance, and decrease a person's percent body fat for desired muscle definition. Among the most widely used are high protein drinks, pre-workout blends and caffeinated energy drinks, branched-chain amino acids (BCAA), glutamine, arginine, essential fatty acids, creatine, HMB, whey protein, ZMA, and weight loss products. Supplements are sold either as single ingredient preparations or in the form of "stacks" – proprietary blends of various supplements marketed as offering synergistic advantages.
While the initial consolidation of Air Force laboratories reduced overhead and budgetary pressure, another push towards a unified laboratory structure came in the form of the National Defense Authorization Act for Fiscal Year 1996, Section 277. This section instructed the Department of Defense to produce a five-year plan for consolidation and restructuring of all defense laboratories. The currently existing laboratory structure was created in October 1997 through the consolidation of Phillips Laboratory headquartered in Albuquerque, New Mexico, Wright Laboratory in Dayton, Ohio, Rome Laboratory (formerly Rome Air Development Center) in Rome, New York, and Armstrong Laboratory in San Antonio, Texas and the Air Force Office of Scientific Research (AFOSR). The single laboratory concept was developed and championed by Maj Gen Richard Paul, who was Director of Science & Technology for AFMC and Gen Henry Viccellio Jr, and then became the first Commander of AFRL.
Galega officinalis (French lilac) was used in diabetes treatment for centuries. In the 1920s, guanidine compounds were discovered in Galega extracts. Animal studies showed that these compounds lowered blood glucose levels. Some less toxic derivatives, synthalin A and synthalin B, were used for diabetes treatment, but after the discovery of insulin, their use declined. Biguanides were reintroduced into Type 2 diabetes treatment in the late 1950s. Initially phenformin was widely used, but its potential for sometimes fatal lactic acidosis resulted in its withdrawal from most pharmacopeias (in the U.S. in 1978). Metformin has a much better safety profile, and it is the principal biguanide drug used in pharmacotherapy worldwide.
The AAA proteins contain two domains, an N-terminal alpha/beta domain that binds and hydrolyzes nucleotides (a Rossmann fold) and a C-terminal alpha-helical domain. The N-terminal domain is 200-250 amino acids long and contains Walker A and Walker B motifs, and is shared in common with other P-loop NTPases, the superfamily which includes the AAA family. Most AAA proteins have additional domains that are used for oligomerization, substrate binding and/or regulation. These domains can lie N- or C-terminal to the AAA module. Some classes of AAA proteins have an N-terminal non-ATPase domain which is followed by either one or two AAA domains (D1 and D2). In some proteins with two AAA domains, both are evolutionarily well conserved (like in Cdc48/p97). In others, either the D2 domain (like in Pex1p and Pex6p) or the D1 domain (in Sec18p/NSF) is better conserved in evolution. While the classical AAA family was based on motifs, the family has been expanded using structural information and is now termed the AAA family.
CGRP antagonists can be used for both acute migraine treatment as well as prophylactically. CGRP is a neuropeptide which is thought to induce migraines via vasodilation of cranial arteries. CGRP can also release inflammatory agents and cause nervous system sensitization. It is theorized that by antagonizing the CGRP receptor of the trigeminal ganglia, lowered CGRP is released and less migraine occurs. Erenumab is a highly selective human monoclonal antibody which is a promising new development in migraine treatment. It has low risk of hepatoxicity like gepants can have, due to being mostly eliminated via proteolysis. There have been some studies suggesting the benefit of using melatonin for prophylaxis of migraine, however, there is a lack of strength of evidence due to a low number of studies as well as conflicting results. Melatonin has a good safety profile but there have been rare instances of serious side effects. More studies are needed in order to suggest the therapeutic use of melatonin for prophylaxis of migraine.
Sources: en.wikipedia.org
Lyophilized powders are typically kept desiccated at -20 °C or below. Reconstituted solutions require a defined buffer, pH, and storage condition based on available stability data.
A certificate commonly lists sequence, lot number, appearance, purity method, purity value, mass confirmation, and storage guidance. It may also note counterion, water content, and test date.
Not always, but independent testing reduces reliance on a supplier's internal result. It is common when a material is used in regulated or repeatable work.
It usually refers to the relative area of the main peak in a chromatographic separation, such as RP-HPLC. It estimates the proportion of UV-absorbing material in that peak, not the absolute mass fraction of the target peptide. Different methods can give different percentages.